Teach you how to install a stainless steel tapered flagpole
Release time:
2021-08-13
1. Install Shunfeng Ball Components 1. If the head of the steel rope has burrs, cut off a little with pliers, and try to make the head of the steel rope as neat as possible. 2. Then insert the steel rope into the small hole of the crown seat, insert the steel rope in until there is a steel rope coming out of the center of the downwind base, and then grab the steel rope and pull out more of the steel rope. 3. Attach a weight with a diameter smaller than that of the flagpole to ensure that it can slide to the bottom when the flagpole is erected. 4. Finally, use 4 M5X10 stainless steel bolts to fix the downwind ball assembly to the top of the flagpole to ensure that the downwind ball can rotate flexibly. Two, erect a flagpole 1. For flagpoles with lower height and lighter weight, the use of cranes can be manually installed according to the actual situation. Install the flagpole on the base. Screw on four nuts to fix the flagpole. 2. Use four screws to calibrate the verticality of the flagpole. Three, install the flag components 1. Put a lock on the steel rope outside the flagpole for use. Pass the head of the steel rope down through the small hole on the upper end of the flag-hanging piece, pass the flag-hanging piece and then wear a lock, tie the steel rope to one end of the tension spring, and pass the head of the steel rope into the lock in the opposite direction , Tighten the lock, and cut off the excess steel rope. Temporarily tie the hanging flag to the flagpole. 2. Install the lower end of the flag piece to untie the knot of the prayer beads, and put the prayer beads on the flagpole. Then connect the prayer beads to the lower end of the flagpole. 3. When hanging, make the angle between the bead and the flag pole greater than 45 degrees. Four, manual device component installation 1. At the appropriate height of the flagpole, generally about 1.2m from the horizontal, there is a rectangular window (installed at the factory). Unscrew the three screws of the manual device assembly, and reach into the window to pull the cable out. 2, use a small hammer to secure the head of the cable and the fixing hole. 3. Put the cable connector made in the previous step through the keyhole and place it on the rolling position of the manual device. Please pay attention to the direction of the cable and tighten it. 4. Put the manual device into the flagpole and lock three screws. Five, debugging 1. The function and use of the crank: This system uses a hand-controlled crank to raise and lower the flag, and use the crank to operate during normal work. There are "down, "up" on the hand control panel, Basic usage: "Raise" and "Lower" correspond to the two actions of raising and lowering the flag. Pull out the crank to realize the stop function. 2. Align the mouth of the crank handle with the manual device assembly, insert it, and turn it clockwise and counterclockwise. If it is stuck or rotates hard, please check whether there is a cable in place or entangled inside. 3. Follow the signs "up" and "down" on the panel, shake the handle, and observe whether the rising and falling directions of the flag (or hanging flag) are uniform. Precautions: 1. When hoisting the flagpole, please be careful not to scratch the flagpole, so as not to affect the appearance. 2, the length of the cable should be moderate, too long, easy to twist. 3. The flagpole is raised to the top, and must not continue to rise with brute force. 4. Please take off the flag if it is not used for a long time, and then raise the flag to the top. 5. When the flag is not hung, please raise the flag to the top.
1. Install Shunfeng Ball Components
1. If the head of the steel rope has burrs, cut off a little with pliers, and try to make the head of the steel rope as neat as possible.
2. Then insert the steel rope into the small hole of the crown seat, insert the steel rope in until there is a steel rope coming out of the center of the downwind base, and then grab the steel rope and pull out more of the steel rope.
3. Attach a weight with a diameter smaller than that of the flagpole to ensure that it can slide to the bottom when the flagpole is erected.
4. Finally, use 4 M5X10 stainless steel bolts to fix the downwind ball assembly to the top of the flagpole to ensure that the downwind ball can rotate flexibly.
Two, erect a flagpole
1. For flagpoles with lower height and lighter weight, the use of cranes can be manually installed according to the actual situation. Install the flagpole on the base. Screw on four nuts to fix the flagpole.
2. Use four screws to calibrate the verticality of the flagpole.
Three, install the flag components
1. Put a lock on the steel rope outside the flagpole for use. Pass the head of the steel rope down through the small hole on the upper end of the flag-hanging piece, pass the flag-hanging piece and then wear a lock, tie the steel rope to one end of the tension spring, and pass the head of the steel rope into the lock in the opposite direction , Tighten the lock, and cut off the excess steel rope. Temporarily tie the hanging flag to the flagpole.
2. Install the lower end of the flag piece to untie the knot of the prayer beads, and put the prayer beads on the flagpole. Then connect the prayer beads to the lower end of the flagpole.
3. When hanging, make the angle between the bead and the flag pole greater than 45 degrees.
Four, manual device component installation
1. At the appropriate height of the flagpole, generally about 1.2m from the horizontal, there is a rectangular window (installed at the factory). Unscrew the three screws of the manual device assembly, and reach into the window to pull the cable out.
2, use a small hammer to secure the head of the cable and the fixing hole.
3. Put the cable connector made in the previous step through the keyhole and place it on the rolling position of the manual device. Please pay attention to the direction of the cable and tighten it.
4. Put the manual device into the flagpole and lock three screws.
Five, debugging
1. The function and use of the crank: This system uses a hand-controlled crank to raise and lower the flag, and use the crank to operate during normal work. There are "down, "up" on the hand control panel,
Basic usage: "Raise" and "Lower" correspond to the two actions of raising and lowering the flag. Pull out the crank to realize the stop function.
2. Align the mouth of the crank handle with the manual device assembly, insert it, and turn it clockwise and counterclockwise. If it is stuck or rotates hard, please check whether there is a cable in place or entangled inside.
3. Follow the signs "up" and "down" on the panel, shake the handle, and observe whether the rising and falling directions of the flag (or hanging flag) are uniform.
Precautions:
1. When hoisting the flagpole, please be careful not to scratch the flagpole, so as not to affect the appearance.
2, the length of the cable should be moderate, too long, easy to twist.
3. The flagpole is raised to the top, and must not continue to rise with brute force.
4. Please take off the flag if it is not used for a long time, and then raise the flag to the top.
5. When the flag is not hung, please raise the flag to the top.
Key words:
Previous
Next
Previous ：
Next：
Recommend